|
MGI JETvarnish 3D
|
Printing Technology
|
MGI's Inkjet Drop-on-Demand technology
Piezo heads mounted on a solid plate covering the entire width Single pass printing Flexible & scalable printing architecture |
Coating Thicknesses |
Depending on your file and the paper used, the coating thickness can vary: * with the Twin option |
Production Speed
|
Up to 3,000 B2 sheet size per hour (flat spot UV coating)
First page out in 16 sec. (no preheating or system latency) |
Registration
|
Left & right side lay guides on either side of the sheet. Overall registration of +/- 200 microns
New feature of automated registration using 2 on-board cameras - optical detection of crop marks |
Formats
|
Minimum: 21x30 cm / 8 x 11.8”
Maximum: 52x74 cm / 20x29" (regular size) 52x105 cm / 20x42” (extended size) |
Paper Thickness
|
Automatic height-adjustment print heads
From 135 gsm to 600 gsm/50 to 220lb |
Substrates
|
Printing on matte or glossy laminated surfaces, with or without aqueous coating, layered paper, plastic, PVC, Polypropylene and other coated materials. NEW - 3D spot UV coat directly onto digital prints (ie. MGI Meteor) with no lamination or coating required. |
Printing Area
|
51.5x73.5 cm (standard)
51.5x104.5 cm (extended) |
Coating and Special Inks
|
New UV coatings specially formulated - with or without 3D raised effects
|
Yields
|
The JETvarnish 3D comes standard with 2 coating tanks and 2 coating circuits allowing a quick changeover between coatings. The first tank has a high capacity volume (18 liters / 4.7 US gal.). The second one is a recyclable 6 liters / 1.59 US gallon bag.
“On-the-fly” tank changeover possible during production without any interruption. Capacity of ink circuit during operation - approximately 1 liter / 0.26 US gal. |
Feeder
|
|
Stacker
|
High capacity stacker able to accomodate stacks up to 60cm/23.6” high
Approximately 4,000 sheets at 135 gsm. Now includes a blowing system to cool down production. |
Paper Path
|
100% flat path
Vacuum feed system Automatic double sheet detection |
In-Line UV Dryer
|
“On-the-fly” drying & curing via integrated UV lamps
Spot Coated sheets can be immediately finished or handled, no additional drying time required |
Front End System
|
New large touch screen (68cm/27") Dedicated PC (with mouse/keyboard) |
Built-in Application Software
|
- Comprehensive job queue management
- Predictive printing cost calculator (coating consumption) - Dedicated image editor to do local and fast image editing prior to production |
Dry Air
|
A dry air compressor of 6 bar @ 15 l/mn (0.41PSI @ 4 gal/mn) is provided, but can be replaced by on-site air system
|
Maintenance and Technical Support
|
Daily maintenance completed in less than 10 minutes Majority of procedures are automated Remote troubleshooting & support via included video/web camera (high speed internet connection required) |
Operator Panel
|
Integrated user-friendly touch-screen LCD.
|
Option(s)
|
-Twin option: 2nd print engine (T2) to double 3D print speed and coating thickness, up to 200 microns -iFOIL option: a hot foil stamping module that connects inline with the JETvarnish 3D |
Eco Friendly
|
Eliminates resource waste (wasted electricity, paper and varnish)
No plates (offset) or screens (screen printing) No messy cleanup or preparation between jobs Drastic reduction in amount of consumables and use of bulk packaging Coating without volatile solvent (no VOC) |
Electrical Requirements
|
30 kW (32 A) 400 Volts - 1 plug CEE/IP44 63A (3P+N+E)
3.7 kW (16 A) 220 Volts - 1 plug CEE/7 16A (2P+E) 2 kW (16 A) 220 Volts - 2 plugs CEE/7 16A (2P+E) |
Operating Environment
|
Temperature: 18 to 30°C / 64 to 86°F
Relative humidity: between 30 and 50% (no condensation) |
Dimensions (L x W x H) | 7.67 x 2.24 x 2.16 meter (with all doors opened) 1 meter / 3.3’ clearance required on all 4 sides Weight: ± 2,150 kg / ± 4,470 lbs |